#DUCT SEAL PUTTY INSTALL#
#DUCT SEAL PUTTY CODE#
#DUCT SEAL PUTTY TV#

Step 2 – An approved degreasing wipe should be used to remove all concrete, dirt, dust and oil residues from the inside 20-30mm of the duct or building entry. For any running water applications please contact us. Cut off any cable ties to enable thorough cleaning of the cables and the duct. Step 1 – Ensure the cable duct opening is clear, removing any debris which may interfere with the installation of the RISE Duct Seal. Installation for watertight and gastight cable duct, substation or building entry applications:

#DUCT SEAL PUTTY CODE#

Resistant to submersion in petrol, diesel and synthetic transmission oilsįire, Gas & Watertight Duct Seal Order Code.

Cost effective protection of cable ducts against water, gas and fire.

Substation flood protection and protects against harmful gas ingress through unsealed ducts.

#DUCT SEAL PUTTY INSTALL#

Quick and easy to install duct sealing system.

Re-enterable duct seal for adding LV, MV & HV cables.

Resistant to corrosive gas including methane, hydrogen sulphide and chlorine.

Trefoil cable sealing of single core LV 11kV 33kV power cables into substations.

Age testing documents no deterioration in sealing performance for more than 50 years.

2 component sealing – i) FIWA sealant ii) rubber insert sleeves.

WIMES approved – Water Industry Mechanical & Electrical Specification accepted.

Compatible with XLPE, EPR and most cable sheaths common to LV 11kV 33kV 66kV 132kV power cable.

Hazardous area cable sealing – ATEX compliant duct seals for Zone 1 & Zone 2 potentially explosive atmospheres.

DSEAR compliant duct seals – congested cable ducts sealed from risk of fire spread and gas explosion.

The CSD RISE system can also be upgraded to provide up to 4 hours of fire protection in accordance with BS EN1366-3 by exchanging the rubber insert sleeves for the fire rated RISE sleeves.Īdding, removing or replacing cables or pipes is also an easy process. Ii) FIWA Sealant – a high quality silicone based, fire stopping and a water repellent sealant. I) RISWAT Sleeves – rubber insert sleeves used to guarantee separation of low, medium and high voltage cables and provide a backing for the sealant layer The RISE Duct Sealing System most commonly used is both gastight and watertight consisting of only two components: I usually fill up at least one 16 oz cup with lead.Īs an added safety margin, I have a 10 gauge steel plate at the back of my trap.CSD RISE Duct Seals – Sealing Cable Ducts (Water Tight & Gas Tight) CSD RISE for Sealing Cable DuctsĬSD RISE Duct Seals are multi-cable and pipe transit sealing systems for cable duct seals, substations and building entries where there is a requirement to prevent the ingress or spread of water, gas and fire.ĬSD Sealing Systems use individual rubber insert sleeves to provide an effective but simple solution to protect against water and gas ingress with the very highest levels of long term cable sealing performance. I use needle nose pliers and remove all the pellets I can find.

#DUCT SEAL PUTTY TV#

Cleaning out the trap is a good sit in front of the TV or fire job. You do get more spash back of lead if you do not clean the lead out of the duct sealant occasionally. I have found that repeated hits to the same spot don't punch the hole deeper, it just builds up a mat of lead about 1' below the surface of the duct sealant. Mine is 2' thick and have not had any penetration problems (RWS 54 22 cal or Kodiak 25 cal). What's the best source to buy it?It is much more firm that plumbers putty.

Is ballistic putty firmer? How much? Please, firsthand experiences only.

My trap already weight 25lb, so I'd rather get a better putty than add duct seal. When it's warm it gets too soft and sticky, and a few shots in the bullseye digs right through it. OK, my trap is made of duct seal ('plumber's putty').

Duct seal putty